Download CAT Soil Compactor 815F BKL Disassembly and Assembly and Diagram Manual SENR9537-04 PDF ( English )

Access the official CAT Soil Compactor 815F BKL Disassembly and Assembly and Diagram Manual SENR9537-04 PDF, the ultimate all-in-one technical reference guide for your Caterpillar 815F soil compactor with BKL prefix and SENR9537-04 publication reference. This comprehensive manual combines step-by-step disassembly and assembly procedures, component removal instructions, installation guidelines, and detailed system diagrams. Ensure correct overhaul and fleet uptime. Download the complete manual PDF instantly. www.themanualsgroup.com

MODEL COVERED :
CAT 815F BKL Soil Compactor

CONTENTS INCLUDED:
Engine
Accessory Drive – Disassemble
Accessory Drive – Install
Accessory Drive – Remove
Air Compressor – Remove and Install
Air Compressor Drive Gear – Install
Air Compressor Drive Gear – Remove
Alternator – Remove and Install
Bearing Clearance – Check
Belt Tensioner – Remove and Install 1
Belt Tensioner – Remove and Install
Camshaft – Install
Camshaft – Remove
Camshaft Bearings – Install
Camshaft Gear – Remove and Install
Camshaft Position Sensor – Remove and Install
Connecting Rod Bearings – Install
Connecting Rod Bearings – Remove
Coolant Temperature Sensor – Remove and Install
Crankshaft – Install
Crankshaft – Remove
Crankshaft Front Seal – Install
Crankshaft Front Seal – Remove
Crankshaft Gear – Remove and Install
Crankshaft Main Bearings – Install
Crankshaft Main Bearings – Remove
Crankshaft Position Sensor – Remove and Install
Crankshaft Rear Seal – Install
Crankshaft Rear Seal – Remove
Crankshaft Rear Seal Carrier – Remove and Install
Cylinder Head – Install
Cylinder Head – Remove
Cylinder Liner – Install
Cylinder Liner – Remove
Electric Starting Motor – Remove and Install
Electronic Control Module – Remove and Install
Electronic Unit Injector – Install
Electronic Unit Injector – Remove
Electronic Unit Injector Sleeve – Install
Electronic Unit Injector Sleeve – Remove
Engine Oil Cooler – Install
Engine Oil Cooler – Remove
Engine Oil Filter Base – Assemble
Engine Oil Filter Base – Disassemble
Engine Oil Filter Base – Install
Engine Oil Filter Base – Remove
Engine Oil Pan – Remove and Install
Engine Oil Pressure Sensor – Remove and Install
Engine Oil Pump – Assemble
Engine Oil Pump – Disassemble
Engine Oil Pump – Install
Engine Oil Pump – Remove
Exhaust Manifold – Remove and Install
Flywheel – Install
Flywheel – Remove
Flywheel Housing – Remove and Install
Front Cover – Install
Front Cover – Remove
Fuel Filter Base – Install
Fuel Filter Base – Remove
Fuel Manifold – Install
Fuel Manifold – Remove
Fuel Priming Pump – Remove and Install
Fuel Transfer Pump – Install
Fuel Transfer Pump – Remove
Gear Group (Front) – Install
Gear Group (Front) – Remove
Housing (Front) – Install
Housing (Front) – Remove
Inlet and Exhaust Valve Guides – Remove and Install
Inlet and Exhaust Valve Springs – Remove and Install
Inlet and Exhaust Valves – Remove and Install
Inlet Manifold – Install
Inlet Manifold – Remove
Lifter Group – Remove and Install
Piston Cooling Jets – Remove and Install
Pistons and Connecting Rods – Assemble
Pistons and Connecting Rods – Disassemble
Pistons and Connecting Rods – Install
Pistons and Connecting Rods – Remove
Rocker Shaft and Pushrod – Install
Rocker Shaft and Pushrod – Remove
Summary of Revisions
Turbocharger – Install
Turbocharger – Remove
Valve Mechanism Cover – Remove and Install
Valve Mechanism Cover Base – Remove and Install
Vibration Damper and Pulley – Remove and Install
Water Outlet Manifold – Install
Water Outlet Manifold – Remove
Water Pump – Assemble
Water Pump – Disassemble
Water Pump – Install manual
Water Pump – Install
Water Pump – Remove
Water Temperature Regulator – Remove and Install
Repair and Schematics
814F Wheel Tractor, 815F Soil Compactor & 816F Landfill Compactor Electrical System
Accumulator Charging Valve (Brake) – Remove and Install
Aftercooler Core – Remove and Install
Alternator – Remove and Install
Axle Housing – Disassemble
Belt Tensioner – Remove and Install
Brake Accumulator – Remove and Install
Brake Control Valve (Parking) – Remove and Install
Brake Control Valve (Service) – Remove and Install
Bulldozer Stabilizer – Install
Bulldozer Stabilizer – Remove 1
Bulldozer Stabilizer – Remove
Cab – Install
Cab – Remove
Carrier Bearing (Drive Shaft) – Remove and Install
Charging System
Cleaner Bar – Install
Cleaner Bar – Remove
Compactor Wheel – Install
Compactor Wheel – Remove
Crankcase Guard – Remove and Install
Crankshaft Front Seal – Install – Engine in Chassis
Crankshaft Front Seal – Remove – Engine in Chassis
Differential and Bevel Gear – Assemble
Differential and Bevel Gear – Disassemble
Differential and Bevel Gear – Install
Differential and Bevel Gear – Remove
Differential Pinion – Assemble
Differential Pinion – Disassemble
Disassembly and Assembly
Drive Shaft (Center) – Remove and Install
Drive Shaft (Front) – Remove and Install
Drive Shaft (Rear) – Remove and Install
Duo-Cone Conventional Seals – Install
Electric Starting Motor – Install – Engine in Chassis
Electric Starting Motor – Remove – Engine in Chassis
Electronic Unit Injector – Install
Electronic Unit Injector – Remove 1
Electronic Unit Injector – Remove
Electronic Unit Injector Sleeve – Install
Engine from Torque Converter, Transmission, Output Transfer Gears – Separate
Engine Oil Cooler – Install – Engine in Chassis
Engine Oil Cooler – Remove – Engine in Chassis
Engine Oil Pump – Install – Engine in Chassis
Engine Oil Pump – Remove – Engine in Chassis
Engine to Torque Converter, Transmission, Output Transfer Gears – Connect
Engine, Torque Converter, Transmission and Output Transfer Gears – Install
Engine, Torque Converter, Transmission and Output Transfer Gears – Remove
Evaporator Coil – Remove and Install
Fan – Remove and Install
Fan Drive – Assemble
Fan Drive – Disassemble
Fan Drive – Install
Fan Drive – Remove
Fan Motor (Air Conditioner and Heater) – Install
Fan Motor (Air Conditioner and Heater) – Remove
Fender and Walkway – Install
Fender and Walkway – Remove
Fixed Axle (Front) – Install
Fixed Axle (Front) – Remove
Fluid Power Graphic Symbols
Front Frame from Rear Frame – Separate
Front Frame to Rear Frame – Connect
Fuel Filter (Secondary) and Fuel Filter Base – Remove and Install – Engine in Chassis
Fuel Priming Pump and Primary Filter (Water Separator) – Remove and Install – Engine in Chassis
Fuel Tank – Install
Fuel Tank – Remove
Fuel Transfer Pump – Remove and Install
Heater Coil – Remove and Install
Hood – Install
Hood – Remove
Hydraulic Oil Cooler – Remove and Install
Hydraulic Tank – Assemble
Hydraulic Tank – Disassemble
Hydraulic Tank – Install
Hydraulic Tank – Remove
Instrument Panel (Front) – Install
Instrument Panel (Front) – Remove
Instrument Panel (Side) – Install
Instrument Panel (Side) – Remove
Lift Cylinder – Remove
Main Control Valve – Assemble
Main Control Valve – Disassemble
Main Control Valve – Install
Main Control Valve – Remove
Metering Pump (Steering) – Assemble
Metering Pump (Steering) – Disassemble
Metering Pump (Steering) – Install
Metering Pump (Steering) – Remove
Modulating Valve (Transmission Clutch) – Assemble
Modulating Valve (Transmission Clutch) – Disassemble
Modulating Valve (Transmission Clutch) – Install
Modulating Valve (Transmission Clutch) – Remove
Muffler – Remove and Install
NoSPIN Differential – Assemble
NoSPIN Differential – Disassemble
Operator Platform – Install
Operator Platform – Remove
Oscillating Axle (Rear) – Install
Oscillating Axle (Rear) – Remove
Output Transfer Gears – Assemble
Output Transfer Gears – Disassemble
Parking Brake – Install 1
Parking Brake – Install
Parking Brake – Remove 1
Parking Brake – Remove
Parking Brake Actuator – Remove and Install
Pilot Valve (Lift and Tilt) – Assemble
Pilot Valve (Lift and Tilt) – Disassemble
Pilot Valve (Lift and Tilt) – Install
Pilot Valve (Lift and Tilt) – Remove
Power Train Guard (Transmission) – Remove and Install
Push Arms and Blade – Install
Push Arms and Blade – Remove
Radiator Bottom Tank – Remove and Install
Radiator Core – Remove and Install
Radiator Guard – Remove and Install
Radiator Top Tank – Remove and Install
Refrigerant Compressor – Remove and Install – Engine in Chassis
Refrigerant Condenser – Remove and Install
Relief Valve (Torque Converter Outlet) – Assemble
Relief Valve (Torque Converter Outlet) – Disassemble
Relief Valve (Torque Converter Outlet) – Install
Relief Valve (Torque Converter Outlet) – Remove
Relief Valve (Transmission Hydraulic Control) – Assemble
Relief Valve (Transmission Hydraulic Control) – Disassemble
Relief Valve (Transmission Hydraulic Control) – Install
Relief Valve (Transmission Hydraulic Control) – Remove
Schematics
Seat – Remove and Install
Service Brake – Install 1
Service Brake – Install
Service Brake – Remove
Stabilizer Link – Remove and Install
Steering Control Valve – Assemble
Steering Control Valve – Disassemble
Steering Control Valve – Install
Steering Control Valve – Remove
Steering Cylinder – Install
Steering Cylinder – Remove
Steering Frame Lock – Separate and Connect
Steering Neutralizer Valve – Remove and Install
Steering Shaft – Remove and Install
Steering Wheel – Remove and Install
Striker Bar – Install
Striker Bar – Remove
System Pressure – Release
Tilt and Tip Cylinder – Install
Tilt and Tip Cylinder – Remove
Tire and Rim (Front) – Remove and Install
Tire and Rim (Rear) – Remove and Install
Torque Converter – Assemble
Torque Converter from Transmission, Output Transfer Gears – Separate
Torque Converter to Transmission, Output Transfer Gears – Connect
Transmission from Output Transfer Gears – Separate
Transmission Oil Cooler – Install – Engine in Chassis
Transmission Oil Cooler – Remove – Engine in Chassis
Transmission Oil Pump – Assemble
Transmission Oil Pump – Disassemble
Transmission Oil Pump – Install
Transmission Oil Pump – Remove
Transmission Planetary – Assemble
Transmission Planetary – Disassemble
Transmission to Output Transfer Gears – Connect
Trunnion Support (Oscillating Axle, Front) – Remove and Install
Trunnion Support (Oscillating Axle, Rear) – Remove and Install
Turbocharger – Install – Engine in Chassis
Turbocharger – Remove – Engine in Chassis
Vane Pump (Steering, Implement, and Pilot) – Install
Vane Pump (Steering, Implement, and Pilot) – Remove
Vane Pump (Steering, Implement, Pilot, Brake) – Assemble
Vane Pump (Steering, Implement, Pilot, Brake) – Disassemble
Water Pump – Install – Engine in Chassis
Water Pump – Remove
Water Temperature Regulator – Remove and Install – Engine in Chassis
Window Wiper and Wiper Motor (Front) – Install
Window Wiper and Wiper Motor (Front) – Remove
Window Wiper and Wiper Motor (Rear) – Install
Window Wiper and Wiper Motor (Rear) – Remove

www.themanualsgroup.com
Download Information 📩: The PDF manual will be emailed to you after your order has been processed by our sales team.