Download Takeuchi Track Loader TL8 TL10 TL12 Operator Manual AU8E003 PDF (English)

Takeuchi Track Loader TL8 TL10 TL12 Operator Manual AU8E003 PDF is a comprehensive guide for operators, technicians, and service professionals working with Takeuchi TL8, TL10, and TL12 track loaders. This manual provides essential operating instructions, safety information, controls and instruments, maintenance procedures, specifications, troubleshooting guidance, and machine care details. The AU8E003 operator manual PDF is a useful reference for understanding proper machine operation, routine servicing, inspections, and maintenance requirements. www.themanualsgroup.com
 
MODEL COVERED :
Takeuchi TL8 TL10 TL12 Loader

CONTENTS INCLUDED :
Cover
Safety alert symbol
Signal words
Introduction
Foreword
Manual storage compartment
Introduction
Serial numbers
Machine description
Front, rear, left and right
Designated operations
Features
Break-in period
Notes on reading this manual
Safety
General precautions
Precautions when preparing
Precautions when starting
Precautions when operating
Precautions when stopping
Precautions when transporting
Precautions on maintenance
Safety signs (decals)
Controls
Names of components
Covers
Ignition key
Fuel filler port
Engine hood
Rear door
Cab
Cab door
Side Window
Emergency exit
Fuse box
Lift arm stopper
Seat and seat belt
Seat
Seat belt
3-point seat belt (optional)
Instrument cluster
Warning lamps
Indicators
Meters
Multi-data display
Switches
Ignition switch
Engine shutdown switch
Horn button
Float button
Throttle controller
Multifunction buttons
Auxiliary hydraulic switches
Travel speed button
Front wiper switch (optional)
Rear wiper switch (optional)
Front light switch
Tail light switch
ECO/Power mode select switch
DPF manual regeneration/inhibit select switch
Auxiliary 1st flow rate select switch
Parking brake switch (TL12 optional)
Ride control switch (TL10/TL12 optional)
Aux. 2nd/14-pin connector select switch (TL10/TL12 optional)
14-pin connector G/H select switch (optional)
Levers and Pedal
Safety Bar
Throttle lever (TL10/TL12)
Throttle pedal (optional)
Right control lever
Left control lever
Accessories
Air conditioner
External power socket
Interior light
Mirrors
Radio (for cab optional)
Auxiliary hydraulic lines (optional)
Aux. 2nd lines (TL10/12 optional)
High-Flow Hydraulic System (If equipped)
Lift arm lower button (If equipped)
Blow by heater lamp
Operation
Before starting operation
Getting on or off the machine
Walk-around inspection
Daily inspection
Starting and stopping the engine
Before starting the engine
Starting the Engine
Warming up the engine
Stopping the engine
Operating the machine
Lever pattern (ISO)
Lever pattern (H)
Warming up the machine (hydraulic oil)
Inspection after warm-up
Traveling the machine
Stopping travel
Operating the working equipment
Operating procedures
Prohibited operations
Cautions on operating
Cautions on traveling on slopes
Operations possible with this machine
Parking the machine
Parking
Inspection and checks after stopping the engine
Handling in cold climates
Preparing for cold climates
Cautions after operations
After the cold climate
Handling rubber tracks
Prohibitions
Cautions
Preventing the rubber tracks from coming off
Transport
Loading and unloading
Hoisting the machine
Securing the machine
Maintenance
General
Maintenance overview
Cautions on maintenance
Service data
Fuel and lubricant table
Regularly replace the hydraulic oil
List of consumables
List of tools
List of tightening torques
Safety-critical parts
Maintenance list
Walk-around inspection
Inspecting by opening the engine hood and rear door
Inspecting by walking around the machine
Inspecting while sitting in the operator’s seat
Daily inspection (every 10 hours)
Inspecting and replenishing the coolant
Inspecting and replenishing the engine oil
Inspecting the water separator
Inspecting the fuel level
Inspecting the hydraulic oil tank level and replenishing
Lubricating the working equipment
After the initial 50 hours (only for new machines)
Replacing the engine oil and the oil filter
Replacing the hydraulic oil return filter
Replacing the pilot line filter
Inspecting and adjusting the fan belt
Inspecting and adjusting the compressor belt (AC)
Every 50 hours
Inspecting and adjusting the track tension
Draining the water from the fuel tank
Inspecting the battery fluid level and replenishing
Inspecting the bucket stoppers (bolts/nuts)
Every 100 hours
Cleaning the water separator
After the initial 250 hours (only for new machines)
Replacing the travel motor gear oil
Every 250 hours
Inspecting and adjusting the fan belt
Inspecting and adjusting the compressor belt (AC)
Replacing the air cleaner element
Cleaning the radiator fins and the oil cooler fins
Cleaning the condenser (AC)
Cleaning the air filters (AC)
Inspecting the refrigerant (gas) level (AC)
Every 500 hours
Replacing the engine oil and the oil filter
Replacing the hydraulic oil return filter
Replacing the pilot line filter
Replacing the travel motor gear oil
Replacing the fuel filters
Adjusting or replacing the bucket stoppers (bolts/nuts)
Every 1000 hours
Cleaning the engine cooling system
Replacing the hydraulic oil and cleaning the suction strainer
Inspecting and adjusting the engine valve clearance
Every 1500 hours
Replacing the oil separator element
Inspecting the injector tip
Inspecting the EGR cooler
Inspecting the PCV valve (TL10/TL12)
Every 3000 hours
Inspecting the turbocharger
Cleaning the DPF
Inspecting the EGR system
When required
Replacing the bucket or attachment
Inspecting and replenishing the windshield washer fluid
Lubricating the levers
Inspecting the rubber tracks
Every year
Replacing the receiver drier
Tilting up the canopy (cab)
Maintenance during extended storage period
Troubleshooting
Symptoms that are not malfunctions
If the engine overheats
If the battery goes dead
If a fuse blows
Inspecting and replacing the fuse
Inspecting the fusible link
Restarting after adding fuel
Bleeding air from the fuel system
If a warning lamp flashes
Vehicle error code list
Engine error code list
Other symptoms
Lowering the lift arms to the ground
Towing
If the cab or canopy is damaged
Specifications
Basic Specifications
Machine dimensions
Operating ranges
Options
General precautions
Safety precautions
Cautions when installing attachments
Cautions when operating attachments
Hydraulic quick-hitch
Replacing the Bucket or Attachment
Quick-Couplers
4-Port quick-coupler (TL10/TL12)
Selecting a lever pattern
Switching the lever pattern
Seat (with a switch function)
Optional equipment mass
California
EC-Conformity Certificate

www.themanualsgroup.com
Download Information 📩 : The PDF manual will be emailed to you after your order has been processed by our sales team.